Treatment of Building in Cologne

TREATMENT OF PLACE CONCRETE SURFACES OF A NEW BUILDING IN COLOGNE

The exterior wall surfaces of the facade (C30 / 37 building – C 40 / 50 cupola, total area approximately 10,600 m2) of the Cologne new building for an Islamic cultural center should not film-forming or color-changing hydrophobic treated. The offering for public tender was 2010 by the architecture office Paul Böhm.

Controll® Topseal was chosen as water-repellent product from multiple tested products. This crucial were the unique features of the product.

As of December 2010 were hydrophobic ca 4,300 m2 of place concrete walls with CRT. In the spring of 2011 are more about 6,300 m2, treated so far still unfinished surfaces (other buildings, minarets, dome, etc.).

After the concrete of façade surfaces had reached most of its final strength, the surfaces were increased by the shell companies with an air hammer with chisel. Then the surfaces were cleaned by the BetonSeal Construction GmbH & Co.KG with air pressure of dust and once in the low pressure spray technique (hand sprayer trade mark Solo) treated with Controll® Topseal. The consumption amounted to approximately 0.2 l / m2. The lower 5 meters of façade area be fitted with a non-film binding semi-permanent graffiti protection after treatment with Controll® Topseal.

Controll® Topseal includes water-soluble potassium Methylsilanetriolate with organic catalyst, which a deep penetrating allows up to 6 cm. As a result are back circulating prevents and frost spalling (E.g. through chill – dew – change) impossible. In addition, it increases the chemical resistance of mineral building materials.

Controll® Topseal is non-toxic and therefore not distinguishing mark according to the hazardous substances regulation. It is colourless, odourless, solvent-free, non-flammable and bio-degradable. Leave no film coating, but a transparent, clear and natural interface.

Controll® Topseal makes a strong water and dirt-resistant surface that prevents moss, fungus or algae infestation and is very easy to clean. The subsoil treated with Controll® Topseal is still protected against efflorescence, environmental factors (air pollution) and UV rays.

Beyond the product properties Controll® Topseal stand out due to low cost and short lay on times.

Warning

Although the technical details and recommendations contained in this data sheet correspond to the best of our knowledge and experience, all the above information must, in every case, be taken as merely indicative and subject to confirmation after long term practical applications; for this reason, anyone who intends to use the Inner and Topseal must ensure before used that it is suitable for the envisaged application in every case. The user alone is fully responsible for any consequences deriving from use of our products.

TESTED AROUND THE WORLD | 100% eco, deep penetrating, no VOC

Nur wenige Produkte wie Controll©Innerseal sind derartig durchleuchtet worden und haben alle Anforderungen in der Welt bestanden

European Official test by Law in all European countries CE, DIN EN 1504-2 System 2+ CE & 1504-8 Certificate for drinking water facilities UNE-DIN EN ISO 12873-2

INNERSEAL EN 1504-2, System 2+: The notified body Identification number 1111 performed the initial inspection of the manufacturing plant and of factory production control and the continuous surveillance, assessment and evaluation of factory production control under system 2+ and issued: Certificate of the yearly conformity of the factory production control 1111-CPR-0556, CE, 1504-2, System 2+ certified, 100% ECO friendly 0% VOC, certified for use with drinking water.

EN 1504-2 Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 2: Surface protection systems for concrete.

INNERSEAL EN 1504-2, System 2+: CE und Zertifikate Herstellung Kontrolle 1111-CPR-0556, 100% ökologisch, kein VOC, Zulassung in Verbindung mit Trinkwasser UNE-EN ISO 12873-2

Zertifizierungsstelle für die Jährliche werkseigene Produktionskontrolle: ist eine staatliche notifizierte Stelle, die die erforderliche Kompetenz und Verantwortlichkeit zur Durchführung der Zertifizierung der werkseigenen Produktionskontrolle nach den vorgegebenen Verfahrens- und Durchführungsregeln besitzt. CE und 2+ prüft sämtliche Produkte und Verfahren von Komsol und nicht nur stichweise.

1504-2 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken - Definitionen, Anforderungen, Qualitätsüberwachung und Beurteilung der Konformität - Teil 2: Oberflächenschutzsysteme für Beton

1504 – 8 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken in Verbindung mit Wasser - Definitionen, Anforderungen, Qualitätskontrolle und AVCP - Teil 8: Qualitätskontrolle und Bewertung und Überprüfung der Leistungsbeständigkeit (AVCP); Deutsche Fassung EN 1504-8:2016

Bitte Hier Klicken

PDF, DIN und BAST

INNERSEAL® Certificado de conformidad anual del control de producción de fábrica 1111-CPR-0556, CE, 1504-2, Sistema 2+ certificado.

100% ECOLÓGICOS 0% libre de COV (compuestos orgánicos volátiles), certificado para su uso en agua potable, EN-CE 1504-2 Sistema 2+ y 1504-8 Certificado para instalaciones de agua potable UNE-EN ISO 12873-2

EN 1504-2, Sistema 2+: El Número de identificación 1111 otorgado por organismo notificado, realiza la inspección inicial de la planta de fabricación, del control de producción de fábrica y la vigilancia y evaluación continua del control de la producción de fábrica bajo el sistema 2+ y emitido:

Certificado de conformidad anual del control de producción de fábrica 1111-CPR-0556, CE, 1504-2, Sistema 2+ certificado. Productos y sistemas para la protección y reparación de estructuras de hormigón - Definiciones, requisitos, control de calidad y evaluación de la conformidad - Parte 2: Sistemas de protección de superficies para hormigón.

PDF Importancia del Sistema 1504-2 sistema 2+