CONTROLL® INNERSEAL +
Innerseal Plus(+) reinforces concrete surfaces against heavy wear and tear as well as providing protection against chlorides and aggressive liquids. The protection is open to diffusion, long-lasting and acid resistant.
Innerseal Plus(+) is a surface reinforcement and protecting treatment for vulnerable concrete areas such as industrial floors and in multi-storey car parks. Innerseal Plus(+) is also used to harden surfaces and for binding dust during grinding and polishing of concrete floors. The result is a very impact and scratch resistant surface.
Innerseal Plus(+) penetrates deep into the capillaries, micro- cracks and pores. A reaction then takes place between salts and minerals to form a very hard calcium silicate hydride. This results in a crystalline structure that stops the transport of water but lets vapours pass through (diffusion). Because the protection is deeply seated, it is insensitive to external influences such as abrasion and impacts.
One treatment increases the durability (abrasion resistance) of new concrete by more than 35% as well as reinforcing older weathering concrete, plaster and cement-based self-leveling floor screed.
The treated surface becomes slightly water repellent (hydrophobic) and this is a final treatment. If there is excess damp in the substrate, a deep waterproofing pre-treatment should be done using Controll ®Innerseal.
AREAS OF USE
BENEFITS
Performance tested and approved in accordance with:
EN 1504-2+ (SP/CBI) Products and systems for the protection and
repair of concrete structures – Surface protection systems for concrete
DIN 11622-2 (TÜV)
Chemical resistance for waste / biogas plants
APPLICATION:
Innerseal Plus(+) is delivered ready to use and must not be mixed with other liquids or diluted. Shake the container before use. The surface to be treated must be free of dust, paint, grease or any other coating that may obstruct the substrate’s absorption.
Damage and visible cracks (>1.0 mm) must be repaired prior to treatment. Protect glass, aluminium and other polished or painted surfaces to prevent etching. In the case of splashes, flush immediately with water and, where necessary, clean with acid; e.g. Controll® ConClean.
The temperature during application and for the following 24 hours must be ≥ +5o C. Avoid application in direct sunlight.
Apply with a low pressure spray or impregnation roller and carry out wet-in-wet at least twice with approx. 5-15 min between application, until full saturation is attained. Treat the spray mist with caution as it can travel long distances and cause damage to glass.
On horizontal concrete surfaces, Innerseal Plus(+) can be poured out and kept in motion with a rubber squeegee, brush or polish mop. Prevent dry patches from forming during treatment. Full saturation is attained after approx. 20-30 min. Stop when the Innerseal Plus(+) starts to “gel”, which usually occurs sooner on new concrete. Remove excess, otherwise shiny or white patches may form.
DRYING TIME:
COVER RANGE:
CLEANING:
MAINTENANCE:
HEALTH & SAFETY:
ENVIRONMENT CERTIFICATE / ASSESSMENTS:
CE MARKING
PRODUCT DATA:
MANUFACTURER:
INTERNATIONAL SALES, TRAINING AND SUPPORT:
TESTED AROUND THE WORLD | 100% eco, deep penetrating, no VOC
Nur wenige Produkte wie Controll©Innerseal sind derartig durchleuchtet worden und haben alle Anforderungen in der Welt bestanden
European Official test by Law in all European countries CE, DIN EN 1504-2 System 2+ CE & 1504-8 Certificate for drinking water facilities UNE-DIN EN ISO 12873-2
INNERSEAL EN 1504-2, System 2+: The notified body Identification number 1111 performed the initial inspection of the manufacturing plant and of factory production control and the continuous surveillance, assessment and evaluation of factory production control under system 2+ and issued: Certificate of the yearly conformity of the factory production control 1111-CPR-0556, CE, 1504-2, System 2+ certified, 100% ECO friendly 0% VOC, certified for use with drinking water.
EN 1504-2 Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 2: Surface protection systems for concrete.
INNERSEAL EN 1504-2, System 2+: CE und Zertifikate Herstellung Kontrolle 1111-CPR-0556, 100% ökologisch, kein VOC, Zulassung in Verbindung mit Trinkwasser UNE-EN ISO 12873-2
Zertifizierungsstelle für die Jährliche werkseigene Produktionskontrolle: ist eine staatliche notifizierte Stelle, die die erforderliche Kompetenz und Verantwortlichkeit zur Durchführung der Zertifizierung der werkseigenen Produktionskontrolle nach den vorgegebenen Verfahrens- und Durchführungsregeln besitzt. CE und 2+ prüft sämtliche Produkte und Verfahren von Komsol und nicht nur stichweise.
1504-2 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken - Definitionen, Anforderungen, Qualitätsüberwachung und Beurteilung der Konformität - Teil 2: Oberflächenschutzsysteme für Beton
1504 – 8 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken in Verbindung mit Wasser - Definitionen, Anforderungen, Qualitätskontrolle und AVCP - Teil 8: Qualitätskontrolle und Bewertung und Überprüfung der Leistungsbeständigkeit (AVCP); Deutsche Fassung EN 1504-8:2016
Bitte Hier Klicken
PDF, DIN und BAST
INNERSEAL® Certificado de conformidad anual del control de producción de fábrica 1111-CPR-0556, CE, 1504-2, Sistema 2+ certificado.
100% ECOLÓGICOS 0% libre de COV (compuestos orgánicos volátiles), certificado para su uso en agua potable, EN-CE 1504-2 Sistema 2+ y 1504-8 Certificado para instalaciones de agua potable UNE-EN ISO 12873-2
EN 1504-2, Sistema 2+: El Número de identificación 1111 otorgado por organismo notificado, realiza la inspección inicial de la planta de fabricación, del control de producción de fábrica y la vigilancia y evaluación continua del control de la producción de fábrica bajo el sistema 2+ y emitido:
Certificado de conformidad anual del control de producción de fábrica 1111-CPR-0556, CE, 1504-2, Sistema 2+ certificado. Productos y sistemas para la protección y reparación de estructuras de hormigón - Definiciones, requisitos, control de calidad y evaluación de la conformidad - Parte 2: Sistemas de protección de superficies para hormigón.
PDF Importancia del Sistema 1504-2 sistema 2+
Komsol product are REACH registered for the enviroment protection
REACH is a regulation of the European Union ---
https://echa.europa.eu/documents/10162/13552/reach_roadmap_2018_web_final_en.pdf
Die REACH-Verordnung ist eine Verordnung der Europäischen Union: ---
https://echa.europa.eu/de/regulations/reach/understanding-reach
REACH es un reglamento de la Unión Europea ---
https://echa.europa.eu/es/regulations/reach/understanding-reach
