HOW DOES CONTROLL® INNERSEAL WORK?

Typical concrete has a great number of pores, voids and capillary paths through which water is transported. It´s through these openings that water can enter and cause damage making waterproofing necessary. When Controll® Innerseal is applied to concrete, the cracks, pores and voids are plugged, and as a result, the concrete will gradually dry out.

CLOSER LOOK

Let´s take a closer look at how Controll® Innerseal works. Water flows through capillary paths, micro cracks and pores in the concrete. These pores have a width between 0.1 and 0.4 mms in diameter. When applied, the chemicals within Controll® Innerseal are absorbed into the concrete and create a catalytic reaction that causes long, narrow crystals to form, which subsequently fill the pores, capillary paths and micro cracks.

capillary-system-komsol-controll-inerseal

Capillary System 1 x 1 mm

Crystallisation

The crystal formation that occurs results in the blocking of pathways and the concrete becomes waterproof. Controll® Innerseal has been designed to penetrate deeply and become an integral part of the concrete and is equally effective against both positive or negative hydrostatic pressure.

The sodium silicate components within Controll® Innerseal react with the calcium hydroxide present in all concrete and as a result forms calcium silicate hydrate which fills the small pores and micro cracks to seal the concrete internally.

Air is still permitted to pass through the crystal formations avoiding water vapour to build up inside the concrete.

Fill small pores

Special protection

If new cracks appear then any water that does pass will react with dormant Controll® Innerseal chemicals causing new crystals to form and grow and again to fill the pores and cracks to make the concrete waterproof.

As well as protecting against water penetration and resulting damage, Controll® Innerseal protects concrete against :

– Acid rain and other chemicals
– Seawater
– Industrial waste and corrosive groundwater

and improves the frost resistance and compressive strength of the concrete.

Controll® Innerseal has been on the market for more than 45 years and has helped several thousand clients worldwide.

Warning

Although the technical details and recommendations contained in this data sheet correspond to the best of our knowledge and experience, all the above information must, in every case, be taken as merely indicative and subject to confirmation after long term practical applications; for this reason, anyone who intends to use the Inner and Topseal must ensure before used that it is suitable for the envisaged application in every case. The user alone is fully responsible for any consequences deriving from use of our products.

TESTED AROUND THE WORLD | 100% eco, deep penetrating, no VOC

Nur wenige Produkte wie Controll©Innerseal sind derartig durchleuchtet worden und haben alle Anforderungen in der Welt bestanden

European Official test by Law in all European countries CE, DIN EN 1504-2 System 2+ CE & 1504-8 Certificate for drinking water facilities UNE-DIN EN ISO 12873-2

INNERSEAL EN 1504-2, System 2+: The notified body Identification number 1111 performed the initial inspection of the manufacturing plant and of factory production control and the continuous surveillance, assessment and evaluation of factory production control under system 2+ and issued: Certificate of the yearly conformity of the factory production control 1111-CPR-0556, CE, 1504-2, System 2+ certified, 100% ECO friendly 0% VOC, certified for use with drinking water.

EN 1504-2 Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 2: Surface protection systems for concrete.

INNERSEAL EN 1504-2, System 2+: CE und Zertifikate Herstellung Kontrolle 1111-CPR-0556, 100% ökologisch, kein VOC, Zulassung in Verbindung mit Trinkwasser UNE-EN ISO 12873-2

Zertifizierungsstelle für die Jährliche werkseigene Produktionskontrolle: ist eine staatliche notifizierte Stelle, die die erforderliche Kompetenz und Verantwortlichkeit zur Durchführung der Zertifizierung der werkseigenen Produktionskontrolle nach den vorgegebenen Verfahrens- und Durchführungsregeln besitzt. CE und 2+ prüft sämtliche Produkte und Verfahren von Komsol und nicht nur stichweise.

1504-2 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken - Definitionen, Anforderungen, Qualitätsüberwachung und Beurteilung der Konformität - Teil 2: Oberflächenschutzsysteme für Beton

1504 – 8 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken in Verbindung mit Wasser - Definitionen, Anforderungen, Qualitätskontrolle und AVCP - Teil 8: Qualitätskontrolle und Bewertung und Überprüfung der Leistungsbeständigkeit (AVCP); Deutsche Fassung EN 1504-8:2016

Bitte Hier Klicken

PDF, DIN und BAST

INNERSEAL® Certificado de conformidad anual del control de producción de fábrica 1111-CPR-0556, CE, 1504-2, Sistema 2+ certificado.

100% ECOLÓGICOS 0% libre de COV (compuestos orgánicos volátiles), certificado para su uso en agua potable, EN-CE 1504-2 Sistema 2+ y 1504-8 Certificado para instalaciones de agua potable UNE-EN ISO 12873-2

EN 1504-2, Sistema 2+: El Número de identificación 1111 otorgado por organismo notificado, realiza la inspección inicial de la planta de fabricación, del control de producción de fábrica y la vigilancia y evaluación continua del control de la producción de fábrica bajo el sistema 2+ y emitido:

Certificado de conformidad anual del control de producción de fábrica 1111-CPR-0556, CE, 1504-2, Sistema 2+ certificado. Productos y sistemas para la protección y reparación de estructuras de hormigón - Definiciones, requisitos, control de calidad y evaluación de la conformidad - Parte 2: Sistemas de protección de superficies para hormigón.

PDF Importancia del Sistema 1504-2 sistema 2+