Waterproofing of a New Building

WATERPROOFING A BASEMENT OF THE NEW BUILDING

The default of the private developers required the construction of open to diffusion, monolithic cellar and garage walls from WU concrete without including a bituminous external seals according to DIN 18195 part 6 (8-2000) as well as the exclusion of the use of vapour density insulating materials. The concrete surfaces in contact with the Earth were treated from outside and inside fully with Controll® Innerseal..

The exterior walls 3 times with 30 minutes interval and the interior walls 2 times with 30 minutes interval, immediately after the discharge of formwork, i.e. after a day of switching time.

A water-impermeable but permeable structure was achieved through this way of „Young concrete“. The lambda value improved up to a 20%. The concrete was permanently protected against improper water inlet and humic acids. Through the crystalline structure of the CRI, the steel reinforcement (c = 5 cm) is permanent protected against corrosion fracture or premature carbonation. After the treatment the soil could be filled just 1-2 days later again. and indoors after about 14 days a lime cement plasters are applied. Later, the surface version was produced with a diffusion-open silicate paint.

Controll® Innerseal makes concretes impervious to water against both, positive and negative hydrostatic pressure, and is an active a deeply urgent corrosion protection of reinforcement steel in concrete (Deep penetration > 195 mm). Also, any harmful salts in the mineral building material cast out during the crystallization and curing process.

Beyond the product properties Controll® Innerseal and Controll® Topseal stand out due to low cost and short lay on times.

We give a product warranty on the effect of Controll® Innerseal and Controll® Topseal by 10 years.

Внимание

Въпреки че техническите подробности и препоръки, съдържащи се в този информационен лист, отговарят на най-доброто от нашите знания и опит, цялата горепосочена информация трябва във всеки случай да се приема само като ориентировъчна и да подлежи на потвърждение след дългосрочни практически приложения; поради тази причина всеки, който възнамерява да използва Inner и Topseal, трябва да се увери, че преди да го използва, е подходящ за предвиденото приложение във всеки случай. Потребителят сам е изцяло отговорен за всички последици, произтичащи от използването на нашите продукти.

ИЗПИТВАНИ ПО СВЕТА

Nur wenige Produkte wie Controll©Innerseal sind derartig durchleuchtet worden und haben alle Anforderungen in der Welt bestanden

European Official test by Law in all European countries CE, DIN EN 1504-2 System 2+ CE & 1504-8 Certificate for drinking water facilities UNE-DIN EN ISO 12873-2

INNERSEAL EN 1504-2, System 2+: The notified body Identification number 1111 performed the initial inspection of the manufacturing plant and of factory production control and the continuous surveillance, assessment and evaluation of factory production control under system 2+ and issued: Certificate of the yearly conformity of the factory production control 1111-CPR-0556, CE, 1504-2, System 2+ certified, 100% ECO friendly 0% VOC, certified for use with drinking water.

EN 1504-2 Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 2: Surface protection systems for concrete.

INNERSEAL EN 1504-2, System 2+: CE und Zertifikate Herstellung Kontrolle 1111-CPR-0556, 100% ökologisch, kein VOC, Zulassung in Verbindung mit Trinkwasser UNE-EN ISO 12873-2

Zertifizierungsstelle für die Jährliche werkseigene Produktionskontrolle: ist eine staatliche notifizierte Stelle, die die erforderliche Kompetenz und Verantwortlichkeit zur Durchführung der Zertifizierung der werkseigenen Produktionskontrolle nach den vorgegebenen Verfahrens- und Durchführungsregeln besitzt. CE und 2+ prüft sämtliche Produkte und Verfahren von Komsol und nicht nur stichweise.

1504-2 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken - Definitionen, Anforderungen, Qualitätsüberwachung und Beurteilung der Konformität - Teil 2: Oberflächenschutzsysteme für Beton

1504 – 8 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken in Verbindung mit Wasser - Definitionen, Anforderungen, Qualitätskontrolle und AVCP - Teil 8: Qualitätskontrolle und Bewertung und Überprüfung der Leistungsbeständigkeit (AVCP); Deutsche Fassung EN 1504-8:2016

Bitte Hier Klicken

PDF, DIN und BAST

INNERSEAL® Certificado de conformidad anual del control de producción de fábrica 1111-CPR-0556, CE, 1504-2, Sistema 2+ certificado.

100% ECOLÓGICOS 0% libre de COV (compuestos orgánicos volátiles), certificado para su uso en agua potable, EN-CE 1504-2 Sistema 2+ y 1504-8 Certificado para instalaciones de agua potable UNE-EN ISO 12873-2

EN 1504-2, Sistema 2+: El Número de identificación 1111 otorgado por organismo notificado, realiza la inspección inicial de la planta de fabricación, del control de producción de fábrica y la vigilancia y evaluación continua del control de la producción de fábrica bajo el sistema 2+ y emitido:

Certificado de conformidad anual del control de producción de fábrica 1111-CPR-0556, CE, 1504-2, Sistema 2+ certificado. Productos y sistemas para la protección y reparación de estructuras de hormigón - Definiciones, requisitos, control de calidad y evaluación de la conformidad - Parte 2: Sistemas de protección de superficies para hormigón.

PDF Importancia del Sistema 1504-2 sistema 2+