Renovation of a Roof Surface
RENOVATION OF A ROOF SURFACE (CLAY TILES)
By surface erosion damaged (permeable and crumbly) clay roofing tiles were 2 times impregnated with Controll® Topseal. Originally both roofs looked like the rear, 1 week after the treatment, you can see the difference: the roof had to be covered not new – the full water-proof and dirt repellency was restored with the application of Controll® Topseal.
Because Controll® Topseal can fill cracks less than 2 mm and thus a permanent waterproof and positive effect, only a few broken tiles had to be replaced.
Physic-mechanical and optical a qualitatively new roof was very economically produced by treatment with Crontroll® Topseal. (Cost: new covering approximately 135 €/ m2/net compared to the rehabilitation with CRT: circa 15 €/ m2/NET) (Calculated costs for Germany. The prices in other countries may vary) .
Controll® Topseal includes water-soluble potassium Methylsilanetriolate with organic catalyst, which a deep penetrating allows up to 6 cm. As a result are back circulating prevents and frost spalling (E.g. through chill – dew – change) impossible. In addition, it increases the chemical resistance of mineral building materials.
Controll® Topseal is non-toxic and therefore not distinguishing mark according to the hazardous substances regulation. It is colourless, odourless, solvent-free, non-flammable and bio-degradable. Leave no film coating, but a transparent, clear and natural interface.
Controll® Topseal makes a strong water and dirt-resistant surface that prevents moss, fungus or algae infestation and is very easy to clean. The subsoil treated with Controll® Topseal is still protected against efflorescence, environmental factors (air pollution) and UV rays.
Beyond the product properties Controll® Innerseal and Controll® Topseal stand out due to low cost and short lay on times.
We give a product warranty on the effect of Controll® Innerseal and Controll® Topseal by 10 years.
ИЗПИТВАНИ ПО СВЕТА
Nur wenige Produkte wie Controll©Innerseal sind derartig durchleuchtet worden und haben alle Anforderungen in der Welt bestanden
European Official test by Law in all European countries CE, DIN EN 1504-2 System 2+ CE & 1504-8 Certificate for drinking water facilities UNE-DIN EN ISO 12873-2
INNERSEAL EN 1504-2, System 2+: The notified body Identification number 1111 performed the initial inspection of the manufacturing plant and of factory production control and the continuous surveillance, assessment and evaluation of factory production control under system 2+ and issued: Certificate of the yearly conformity of the factory production control 1111-CPR-0556, CE, 1504-2, System 2+ certified, 100% ECO friendly 0% VOC, certified for use with drinking water.
EN 1504-2 Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 2: Surface protection systems for concrete.
INNERSEAL EN 1504-2, System 2+: CE und Zertifikate Herstellung Kontrolle 1111-CPR-0556, 100% ökologisch, kein VOC, Zulassung in Verbindung mit Trinkwasser UNE-EN ISO 12873-2
Zertifizierungsstelle für die Jährliche werkseigene Produktionskontrolle: ist eine staatliche notifizierte Stelle, die die erforderliche Kompetenz und Verantwortlichkeit zur Durchführung der Zertifizierung der werkseigenen Produktionskontrolle nach den vorgegebenen Verfahrens- und Durchführungsregeln besitzt. CE und 2+ prüft sämtliche Produkte und Verfahren von Komsol und nicht nur stichweise.
1504-2 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken - Definitionen, Anforderungen, Qualitätsüberwachung und Beurteilung der Konformität - Teil 2: Oberflächenschutzsysteme für Beton
1504 – 8 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken in Verbindung mit Wasser - Definitionen, Anforderungen, Qualitätskontrolle und AVCP - Teil 8: Qualitätskontrolle und Bewertung und Überprüfung der Leistungsbeständigkeit (AVCP); Deutsche Fassung EN 1504-8:2016
Bitte Hier Klicken
PDF, DIN und BAST
INNERSEAL® Certificado de conformidad anual del control de producción de fábrica 1111-CPR-0556, CE, 1504-2, Sistema 2+ certificado.
100% ECOLÓGICOS 0% libre de COV (compuestos orgánicos volátiles), certificado para su uso en agua potable, EN-CE 1504-2 Sistema 2+ y 1504-8 Certificado para instalaciones de agua potable UNE-EN ISO 12873-2
EN 1504-2, Sistema 2+: El Número de identificación 1111 otorgado por organismo notificado, realiza la inspección inicial de la planta de fabricación, del control de producción de fábrica y la vigilancia y evaluación continua del control de la producción de fábrica bajo el sistema 2+ y emitido:
Certificado de conformidad anual del control de producción de fábrica 1111-CPR-0556, CE, 1504-2, Sistema 2+ certificado. Productos y sistemas para la protección y reparación de estructuras de hormigón - Definiciones, requisitos, control de calidad y evaluación de la conformidad - Parte 2: Sistemas de protección de superficies para hormigón.
PDF Importancia del Sistema 1504-2 sistema 2+
Komsol product are REACH registered for the enviroment protection
REACH is a regulation of the European Union ---
https://echa.europa.eu/documents/10162/13552/reach_roadmap_2018_web_final_en.pdf
Die REACH-Verordnung ist eine Verordnung der Europäischen Union: ---
https://echa.europa.eu/de/regulations/reach/understanding-reach
REACH es un reglamento de la Unión Europea ---
https://echa.europa.eu/es/regulations/reach/understanding-reach
