Heat Improvement of a Home

IMPROVEMENT OF HEAT BALANCE OF SAND-LIME BRICK FAÇADE

The facade of a single-family house was cleaned with a high-pressure Jet device and after the complete drying once treated with Controll® Topseal. To prove that by draining with Controll® Topseal also heating and energy costs can be reduced, a thermograph examination of the facade conducted prior to treatment to the 07.03.2009 and a year later the 03.03.2010. 2009, temperatures were for example at the entrance test point T1 at 1.6 ° C, 2010 at 0.1 ° C. Point T2, 1.2 ° C was measured in 2009, in 2010, there were 0.5 º C. T3 2009 amounted to 2.0 ° C, 2010 at 1.7 ° C. Therefore, an improvement was achieved by an average of 51%.

Controll® Topseal includes water-soluble potassium Methylsilanetriolate with organic catalyst, which a deep penetrating allows up to 6 cm. As a result are back circulating prevents and frost spalling (E.g. through chill – dew – change) impossible. In addition, it increases the chemical resistance of mineral building materials.

Controll® Topseal is non-toxic and therefore not distinguishing mark according to the hazardous substances regulation. It is colourless, odourless, solvent-free, non-flammable and bio-degradable. Leave no film coating, but a transparent, clear and natural interface.

Controll® Topseal makes a strong water and dirt-resistant surface that prevents moss, fungus or algae infestation and is very easy to clean. The subsoil treated with Controll® Topseal is still protected against efflorescence, environmental factors (air pollution) and UV rays.

Внимание

Въпреки че техническите подробности и препоръки, съдържащи се в този информационен лист, отговарят на най-доброто от нашите знания и опит, цялата горепосочена информация трябва във всеки случай да се приема само като ориентировъчна и да подлежи на потвърждение след дългосрочни практически приложения; поради тази причина всеки, който възнамерява да използва Inner и Topseal, трябва да се увери, че преди да го използва, е подходящ за предвиденото приложение във всеки случай. Потребителят сам е изцяло отговорен за всички последици, произтичащи от използването на нашите продукти.

ИЗПИТВАНИ ПО СВЕТА

Nur wenige Produkte wie Controll©Innerseal sind derartig durchleuchtet worden und haben alle Anforderungen in der Welt bestanden

European Official test by Law in all European countries CE, DIN EN 1504-2 System 2+ CE & 1504-8 Certificate for drinking water facilities UNE-DIN EN ISO 12873-2

INNERSEAL EN 1504-2, System 2+: The notified body Identification number 1111 performed the initial inspection of the manufacturing plant and of factory production control and the continuous surveillance, assessment and evaluation of factory production control under system 2+ and issued: Certificate of the yearly conformity of the factory production control 1111-CPR-0556, CE, 1504-2, System 2+ certified, 100% ECO friendly 0% VOC, certified for use with drinking water.

EN 1504-2 Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 2: Surface protection systems for concrete.

INNERSEAL EN 1504-2, System 2+: CE und Zertifikate Herstellung Kontrolle 1111-CPR-0556, 100% ökologisch, kein VOC, Zulassung in Verbindung mit Trinkwasser UNE-EN ISO 12873-2

Zertifizierungsstelle für die Jährliche werkseigene Produktionskontrolle: ist eine staatliche notifizierte Stelle, die die erforderliche Kompetenz und Verantwortlichkeit zur Durchführung der Zertifizierung der werkseigenen Produktionskontrolle nach den vorgegebenen Verfahrens- und Durchführungsregeln besitzt. CE und 2+ prüft sämtliche Produkte und Verfahren von Komsol und nicht nur stichweise.

1504-2 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken - Definitionen, Anforderungen, Qualitätsüberwachung und Beurteilung der Konformität - Teil 2: Oberflächenschutzsysteme für Beton

1504 – 8 Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken in Verbindung mit Wasser - Definitionen, Anforderungen, Qualitätskontrolle und AVCP - Teil 8: Qualitätskontrolle und Bewertung und Überprüfung der Leistungsbeständigkeit (AVCP); Deutsche Fassung EN 1504-8:2016

Bitte Hier Klicken

PDF, DIN und BAST

INNERSEAL® Certificado de conformidad anual del control de producción de fábrica 1111-CPR-0556, CE, 1504-2, Sistema 2+ certificado.

100% ECOLÓGICOS 0% libre de COV (compuestos orgánicos volátiles), certificado para su uso en agua potable, EN-CE 1504-2 Sistema 2+ y 1504-8 Certificado para instalaciones de agua potable UNE-EN ISO 12873-2

EN 1504-2, Sistema 2+: El Número de identificación 1111 otorgado por organismo notificado, realiza la inspección inicial de la planta de fabricación, del control de producción de fábrica y la vigilancia y evaluación continua del control de la producción de fábrica bajo el sistema 2+ y emitido:

Certificado de conformidad anual del control de producción de fábrica 1111-CPR-0556, CE, 1504-2, Sistema 2+ certificado. Productos y sistemas para la protección y reparación de estructuras de hormigón - Definiciones, requisitos, control de calidad y evaluación de la conformidad - Parte 2: Sistemas de protección de superficies para hormigón.

PDF Importancia del Sistema 1504-2 sistema 2+